What does your pool pump do
A swimming pool pump is an essential equipment for efficiently filtering and circulating pool water, leaving you with clean, debris-free, and safe water for your relaxation. When in operation, the pool pump runs continuously, creating the flow of water that circulates the pool water to the filter, heater, and salt chlorinator. Without it, the water wouldn’t be effectively sanitized, leaving you with dirt ridden water that’s contaminated with bacteria. Therefore, the importance of a pool pump cannot be overstated.
Regardless of whether your pool is big or small you will need a pool pump to ensure the water is in the best condition for swimming. Even these pools have pool pumps https://www.travelawaits.com/2667194/the-worlds-largest-swimming-pools/, although most likely a lot larger then the average family home swimming pool.
That said, it’s important to note that your Brisbane pool pump, just like every other mechanical device, requires regular maintenance for it to keep working efficiently. Without a well-functioning pump, maintaining your pool becomes a difficult task. Here are 4 tips on how to maintain your pump and keep it in prime condition.
Perform Regular Checks
As mentioned, your pool is the powerhouse of the entire swimming pool, which means you need to run it every day to keep your pool clean and safe. How long you should to run your pump each day will depend on various factors including the quantity of water your pool holds and the turnover rate. On average your pump should run about eight hours a day. And this means you have to check it on a weekly basis to see if there’s a problem that needs to be addressed.
Some of the parameters to focus on during your routine checks include the water flow, motor temperature, current and voltage, filter’s pressure reading, and running time. Compare these readings with what’s indicated in the owner’s manual. Also, check for damaged seals, unusual vibrations and sounds, and leaks.
The idea is to identify any issues early and prevent costly repairs down the road. Once you suspect any abnormality, contact a Brisbane pool pump repair service technician to fix it.
Clean the Skimmer and Pump Basket
A swimming pool uses a skimmer basket and pump basket to capture larger debris such as sticks and leaves. By trapping these contaminants, these two baskets protect the impeller and filtration system from damage. Over time, debris accumulates in these baskets and, if not removed, they can become clogged, thereby stressing the seals in your Brisbane pool pump.
Clogged baskets also prevent the pump from functioning optimally and you may not get the proper turnover rate for proper filtration. It’s, therefore, important that you clean both the skimmer and pump baskets every week to remove the captured debris.
Ensure Proper Pool Water Level
You probably already know that ensuring proper pool water level is crucial to increasing your swimming pool’s longevity. Not paying attention to your pool water level can have serious implications to your pump and other pool components. The good thing is that you can avoid any damage to your Brisbane pool pump by checking your water levels at least once a week.
Ideally, your pool’s water level should be anywhere between one-third and one-half up your skimmer plate. Remember, your pump and the skimmer in your pool are usually connected by a hose. This means, if your water levels are too low, the pump is likely to suck air rather than water. This can cause serious damage to the pump. High water levels, on the other hand, may leave the debris floating on your pool since it can’t be pulled into the skimmer box. So, be on the look out, and always adjust the water levels as needed.
Clean Your Pool Filters
Your pool’s filter, just like your home’s air filter, requires regular cleaning to remove the dirt, debris, and contaminants it captures and ensure it runs efficiently. When the pool filter becomes clogged with debris, the flow of water through the filter is hindered and the pressure increases. This means the pump has to work harder to circulate the pool water, shortening its life.
So, whether you’re using a sand filter, diatomaceous earth (D.E) filter, or a cartridge filter, be sure to clean your pool filter as soon as the water starts turning cloudy or the pressure gauge starts reading 10 psi above the normal. A clean filter means a clean pool. So, make sure you clean your filter at least once a month. Working with a Brisbane pool pump service is always the best option when it comes to pool equipment cleaning and maintenance.